chip soc/intel/alderlake
	# As per Intel Advisory doc#723158, the change is required to prevent possible
	# display flickering issue.
	register "usb2_phy_sus_pg_disable" = "1"

	# GPE configuration
	register "pmc_gpe0_dw0" = "GPP_A"
	register "pmc_gpe0_dw1" = "GPP_E"
	register "pmc_gpe0_dw2" = "GPP_F"

	# EC host command ranges are in 0x800-0x8ff & 0x200-0x20f
	register "gen1_dec" = "0x00fc0801"
	register "gen2_dec" = "0x000c0201"
	# EC memory map range is 0x900-0x9ff
	register "gen3_dec" = "0x00fc0901"

	# S0ix enable
	register "s0ix_enable" = "true"

	# DPTF enable
	register "dptf_enable" = "true"

	register "tcc_offset" = "10"     # TCC of 90

	# Enable CNVi BT
	register "cnvi_bt_core" = "true"

	register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC0)"	# USB2_C0
	register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC1)"	# USB2_C1
	register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC2)"	# USB2_C2
	register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)"	# NFC
	register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)"	# Type-A Port A3
	register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)"	# Type-A Port A2
	register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)"	# Type-A Port A1
	register "usb2_ports[8]" = "USB2_PORT_MID(OC_SKIP)"	# Type-A Port A0
	register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)"	# M.2 Bluetooth

	register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# Type-A port A0
	register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A port A1(DCI)
	register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A port A2
	register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)"	# Type-A port A3

	register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC0)"
	register "tcss_ports[1]" = "TCSS_PORT_DEFAULT(OC1)"
	register "tcss_ports[2]" = "TCSS_PORT_DEFAULT(OC2)"

	register "serial_io_i2c_mode" = "{
		[PchSerialIoIndexI2C0] = PchSerialIoPci,
		[PchSerialIoIndexI2C1] = PchSerialIoPci,
		[PchSerialIoIndexI2C2] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C3] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C4] = PchSerialIoDisabled,
		[PchSerialIoIndexI2C5] = PchSerialIoDisabled,
	}"

	register "serial_io_gspi_mode" = "{
		[PchSerialIoIndexGSPI0] = PchSerialIoDisabled,
		[PchSerialIoIndexGSPI1] = PchSerialIoPci,
	}"

	register "serial_io_uart_mode" = "{
		[PchSerialIoIndexUART0] = PchSerialIoPci,
		[PchSerialIoIndexUART1] = PchSerialIoDisabled,
		[PchSerialIoIndexUART2] = PchSerialIoDisabled,
	}"

	register "pch_slp_s3_min_assertion_width" = "SLP_S3_ASSERTION_50_MS"
	register "pch_slp_s4_min_assertion_width" = "SLP_S4_ASSERTION_1S"
	register "pch_slp_sus_min_assertion_width" = "SLP_SUS_ASSERTION_1_S"
	register "pch_slp_a_min_assertion_width" = "SLP_A_ASSERTION_98_MS"
	register "pch_reset_power_cycle_duration" = "POWER_CYCLE_DURATION_1S"

	# HD Audio
	register "pch_hda_dsp_enable" = "1"
	register "pch_hda_idisp_link_tmode" = "HDA_TMODE_8T"
	register "pch_hda_idisp_link_frequency" = "HDA_LINKFREQ_96MHZ"
	register "pch_hda_idisp_codec_enable" = "1"

	# FIVR RFI Spread Spectrum 1.5%
	register "fivr_spread_spectrum" = "FIVR_SS_1_5"

	# Disable C state auto-demotion for all brask baseboards
	register "disable_c1_state_auto_demotion" = "true"

	# Intel Common SoC Config
	#+-------------------+---------------------------+
	#| Field             |  Value                    |
	#+-------------------+---------------------------+
	#| GSPI1             | Fingerprint MCU           |
	#| I2C0              | Audio                     |
	#| I2C1              | cr50 TPM. Early init is   |
	#|                   | required to set up a BAR  |
	#|                   | for TPM communication     |
	#+-------------------+---------------------------+
	register "common_soc_config" = "{
		.i2c[0] = {
			.speed = I2C_SPEED_FAST,
		},
		.i2c[1] = {
			.early_init = 1,
			.speed = I2C_SPEED_FAST,
			.rise_time_ns = 600,
			.fall_time_ns = 400,
			.data_hold_time_ns = 50,
		},
	}"

	device domain 0 on
		device ref igpu on end
		device ref dtt on end
		device ref tbt_pcie_rp0 on end
		device ref tbt_pcie_rp1 on end
		device ref tbt_pcie_rp2 on end
		device ref gna on end
		device ref tcss_xhci on end
		device ref tcss_dma0 on end
		device ref tcss_dma1 on end
		device ref xhci on end
		device ref shared_sram on end
		device ref cnvi_wifi on
			chip drivers/wifi/generic
				register "wake" = "GPE0_PME_B0"
				register "add_acpi_dma_property" = "true"
				device generic 0 on end
			end
		end
		device ref i2c1 on
			chip drivers/i2c/tpm
				register "hid" = ""GOOG0005""
				register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)"
				device i2c 50 on end
			end
		end
		device ref heci1 on end
		device ref sata on end
		device ref pcie_rp7 on
			# Enable PCIE 7 using clk 6
			register "pch_pcie_rp[PCH_RP(7)]" = "{
				.clk_src = 6,
				.clk_req = 6,
				.flags = PCIE_RP_LTR | PCIE_RP_AER,
			}"
		end	#PCIE7 RTL8125 Ethernet NIC
		device ref pcie_rp8 on
			# Enable SD Card PCIE 8 using clk 3
			register "pch_pcie_rp[PCH_RP(8)]" = "{
				.clk_src = 3,
				.clk_req = 3,
				.flags = PCIE_RP_HOTPLUG | PCIE_RP_LTR | PCIE_RP_AER,
			}"
		end	#PCIE8 SD card
		device ref uart0 on end
		device ref gspi1 on end
		device ref pch_espi on
			chip ec/google/chromeec
				device pnp 0c09.0 on end
			end
		end
		device ref hda on end
		device ref smbus on end
	end
end