#
# Copyright (c) 2015-2024, Arm Limited and Contributors. All rights reserved.
# Copyright (c) 2024, Mario Bălănică <mariobalanica02@gmail.com>
#
# SPDX-License-Identifier: BSD-3-Clause
#

include lib/xlat_tables_v2/xlat_tables.mk

include drivers/arm/gic/v2/gicv2.mk

PLAT_INCLUDES		:=	-Iplat/rpi/common/include			\
				-Iplat/rpi/rpi5/include

PLAT_BL_COMMON_SOURCES	:=	drivers/arm/pl011/aarch64/pl011_console.S 	\
				plat/rpi/common/rpi3_common.c			\
				plat/rpi/common/rpi3_console_pl011.c		\
				${XLAT_TABLES_LIB_SRCS}

BL31_SOURCES		+=	lib/cpus/aarch64/cortex_a76.S			\
				plat/rpi/common/aarch64/plat_helpers.S		\
				plat/rpi/common/aarch64/armstub8_header.S 	\
				drivers/delay_timer/delay_timer.c		\
				plat/common/plat_gicv2.c			\
				plat/rpi/common/rpi4_bl31_setup.c		\
				plat/rpi/rpi5/rpi5_setup.c			\
				plat/rpi/common/rpi3_pm.c			\
				plat/common/plat_psci_common.c			\
				plat/rpi/common/rpi3_topology.c			\
				${GICV2_SOURCES}

# For now we only support BL31, using the kernel loaded by the GPU firmware.
RESET_TO_BL31		:=	1

# All CPUs enter armstub8.bin.
COLD_BOOT_SINGLE_CPU	:=	0

# Tune compiler for Cortex-A76
ifeq ($(notdir $(CC)),armclang)
    TF_CFLAGS_aarch64	+=	-mcpu=cortex-a76
else ifneq ($(findstring clang,$(notdir $(CC))),)
    TF_CFLAGS_aarch64	+=	-mcpu=cortex-a76
else
    TF_CFLAGS_aarch64	+=	-mtune=cortex-a76
endif

# Add support for platform supplied linker script for BL31 build
$(eval $(call add_define,PLAT_EXTRA_LD_SCRIPT))

# Enable all errata workarounds for Cortex-A76 r4p1
ERRATA_A76_1946160		:= 1
ERRATA_A76_2743102		:= 1

# Add new default target when compiling this platform
all: bl31

# Build config flags
# ------------------

# Disable stack protector by default
ENABLE_STACK_PROTECTOR	 	:= 0

# Have different sections for code and rodata
SEPARATE_CODE_AND_RODATA	:= 1

# Hardware-managed coherency
HW_ASSISTED_COHERENCY		:= 1
USE_COHERENT_MEM		:= 0

# Cortex-A76 is 64-bit only
CTX_INCLUDE_AARCH32_REGS	:= 0

# Platform build flags
# --------------------

# There is not much else than a Linux kernel to load at the moment.
RPI3_DIRECT_LINUX_BOOT		:= 1

# BL33 images can only be AArch64 on this platform.
RPI3_BL33_IN_AARCH32		:= 0

# UART to use at runtime. -1 means the runtime UART is disabled.
# Any other value means the default UART will be used.
RPI3_RUNTIME_UART		:= 0

# Use normal memory mapping for ROM, FIP, SRAM and DRAM
RPI3_USE_UEFI_MAP		:= 0

# SMCCC PCI support (should be enabled for ACPI builds)
SMC_PCI_SUPPORT			:= 0

# Process platform flags
# ----------------------

$(eval $(call add_define,RPI3_BL33_IN_AARCH32))
$(eval $(call add_define,RPI3_DIRECT_LINUX_BOOT))
ifdef RPI3_PRELOADED_DTB_BASE
$(eval $(call add_define,RPI3_PRELOADED_DTB_BASE))
endif
$(eval $(call add_define,RPI3_RUNTIME_UART))
$(eval $(call add_define,RPI3_USE_UEFI_MAP))
$(eval $(call add_define,SMC_PCI_SUPPORT))

ifeq (${ARCH},aarch32)
  $(error Error: AArch32 not supported on rpi5)
endif

ifneq ($(ENABLE_STACK_PROTECTOR), 0)
PLAT_BL_COMMON_SOURCES	+=	drivers/rpi3/rng/rpi3_rng.c		\
				plat/rpi/common/rpi3_stack_protector.c
endif

ifeq ($(SMC_PCI_SUPPORT), 1)
BL31_SOURCES		+=	plat/rpi/common/rpi_pci_svc.c
endif