/*
 * Copyright (C) 2019 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
package android.hardware.automotive.can@1.0;

/**
 * CAN message ID.
 *
 * Does not include any flags like RTR nor ERR, only a plain 11-bit
 * or 29-bit identifier, as defined in CAN 1.x/2.0x.
 *
 * Unused bits must be set to zero.
 */
typedef uint32_t CanMessageId;

/**
 * CAN message being sent or received.
 */
struct CanMessage {
    CanMessageId id;

    /**
     * CAN message payload, as defined in CAN 1.x and CAN 2.x standards.
     *
     * The length of the payload vector directly translates to the length
     * of the data frame (i.e. includes any padding bytes), so it may be in
     * a range of:
     *  - 0-8 bytes for standard CAN;
     *  - up to 64 bytes for CAN FD.
     * ISO TP is not supported directly for now.
     */
    vec<uint8_t> payload;

    /**
     * Time in nanoseconds since boot.
     *
     * Ignored for outgoing messages.
     */
    uint64_t timestamp;

    /**
     * A request to proactively pull certain data from other ECU in CAN network.
     *
     * For details please refer to CAN standard.
     *
     * If this flag is set, payload must be empty.
     */
    bool remoteTransmissionRequest;

    /**
     * Flag indicating if the message has an extended ID.
     *
     * Extended ID's are 29 bits long, as opposed to the standard 11 bit ID.
     * It can not simply be inferred from the length of the ID itself, as the
     * message ID 0x00000123 !=  message ID 0x123.
     */
    bool isExtendedId;
};

/**
 * Single filter rule for CAN messages.
 *
 * A filter is satisfied if:
 * ((receivedId & mask) == (id & mask)) == !exclude
 *
 * In order for set of filters to match, at least one non-exclude filters must match (if there is
 * one) and all exclude filters must match. In other words:
 *  - a single matching non-exclude filter makes the whole set matching;
 *  - a single non-matching excluded filter makes the whole set non-matching.
 */
struct CanMessageFilter {
    CanMessageId id;
    uint32_t mask;
    /** Remote Transmission Request; another ECU requests <DLC> bytes of data on this message ID */
    FilterFlag rtr;
    /** 29 bit message ID is used instead of 11 bits */
    FilterFlag extendedFormat;
    /** 'exclude' *DOES* apply to rtr and extendedFormat! */
    bool exclude;
};


/**
 * Types of filter that can be applied to a CanMessageFilter
 */
enum FilterFlag : uint8_t {
    /** Default, FilterFlag doesn't effect what messages filtered */
    DONT_CARE = 0,
    /** This FilterFlag MUST be present in received messages to pass though the filter */
    SET,
    /** This FilterFlag must NOT be present in received messages to pass though the filter */
    NOT_SET,
};

enum Result : uint8_t {
    OK,
    UNKNOWN_ERROR,
    PAYLOAD_TOO_LONG,
    INTERFACE_DOWN,
    TRANSMISSION_FAILURE,
    INVALID_ARGUMENTS,
};

/**
 * @see ICanMessageListener#onError
 */
enum ErrorEvent : uint8_t {
    UNKNOWN_ERROR,

    /** A problem with CAN interface HW. */
    HARDWARE_ERROR,

    /** CAN interface is down. */
    INTERFACE_DOWN,

    /** TX buffer overflow: client is sending too many packets. */
    TX_OVERFLOW,

    /** RX buffer overflow: client is not reading packets fast enough. */
    RX_OVERFLOW,

    /** Received malformed input. */
    MALFORMED_INPUT,

    /** Bus overload: there is too much traffic on the bus. */
    BUS_OVERLOAD,

    /** Bus error: shorted Hi/Lo line, bus off etc. */
    BUS_ERROR,
};