#
# Lynx sensor device configuration registry script for the pvt stage or later.
#
# Source of truth: go/pixel-sensor-list
#

#
# CDT Filter <CDT>:<mask>
# CDT format: <0xPPPPSJIV> (P:Product, S:Stage, J:Major, I:Minor, V:Variant)
# go/pixel-cdt-whi-pro
#

?+0x50000:0xFFFF0000
# Exclude
?-0x51000:0xFFFFF000  # Dev
?-0x52000:0xFFFFF000  # Proto
?-0x53000:0xFFFFF000  # EVT
?-0x54000:0xFFFFF000  # DVT

#
# Record reg_script.
#

+/
reg_script=lynx_pvt.reg

#
# Buses
#

# I2C
+/dev/i2c/0
  bus_name=i2c0
  bus_index=0

# I3C
+/dev/i3c/2
  bus_name=i3c2
  bus_index=2

# SPI
+/dev/spi/0
  bus_name=spi0
  bus_index=0

# PDM
+/dev/pdm
  base_clk_hz=24576000

#
# Sensors
#

# IMU (LSM6DSV)
+/dev/lsm6dsv/0
  bus_name=i3c2
  bus_freq_hz=400000
  i3c_freq_hz=1230000
  bus_addr=0x6a
  i3c_addr=0xa
  intr_id=47
  trigger_type=2
  fifo_enabled=1
  md_threshold_m_per_s_sq=1.2264
  md_window_ms=20
  sd_window_ms=5000
  fifo_max_odr=4000
  fifo_max_wm=245
  fifo_min_wm=1
+/dev/lsm6dsv/0/accel
  orientation_transform=-2 1 3
+/dev/lsm6dsv/0/gyro
  orientation_transform=-2 1 3
+/dev/lsm6dsv/0/temp
+/dev/lsm6dsv/0/motion_detect
+/dev/lsm6dsv/0/stationary_detect
+/dev/lsm6dsv/0/free_fall_detect
  name=LSM6DSV FreeFall Detect

# MAG (MMC5633NJ)
+/dev/mmc56x3x/0
  bus_name=i3c2
  bus_freq_hz=400000
  i3c_freq_hz=1230000
  bus_addr=0x30
  i3c_addr=0x14
  priority=0
+/dev/mmc56x3x/0/mag
  orientation_transform=-1 -2 3
  fac_cal_transform=1.0288 0.0292 0.0028 0.0154 0.8620 0.0382 -0.0005 0.0781 1.1740 0 0 0

# BARO (ICP20100)
+/dev/icp20100/0
  bus_name=i2c0
  bus_freq_hz=400000
  bus_addr=0x63
  intr_id=37
  min_period_us=25000
+/dev/icp20100/0/baro
+/dev/icp20100/0/temp

# ALSP1 (TMD37193)
+/dev/tmd3719/0
  bus_name=i2c0
  bus_freq_hz=400000
  bus_addr=0x39
  intr_id=15
  sync_delay_ns=1766535
  # falling edge = 0, rising edge = 1
  te2_alignment=0
  anti_aliasing=1
+/dev/tmd3719/0/als
  lux_scale=1.934868
  c_coef=1
  r_coef=-0.674221
  g_coef=1.615560
  b_coef=-1.941339
  itime_table_brightness=70 160 256 368 2048
  itime_table=1923290 1494680 1036240 504560 181750
  max_gain_table=11 10 10 9 8
  fast_filter_size=10
  slow_filter_size=100
  aod_fast_filter_size=2
  aod_slow_filter_size=2
  max_lux=160000
  # Number of EM cycles in a 60Hz frame.
  EM_cycle_count_60Hz=6
  # Step-size (in EM slots) for each rotation.
  rotation_step_size=1
  new_gain_ratio=1

  clear_gain11_ratio=0.114538
  red_gain11_ratio=0.113578
  green_gain11_ratio=0.112715
  blue_gain11_ratio=0.112578

  clear_gain10_ratio=0.241402
  red_gain10_ratio=0.240592
  green_gain10_ratio=0.239849
  blue_gain10_ratio=0.239748

  clear_gain9_ratio=0.494349
  red_gain9_ratio=0.493746
  green_gain9_ratio=0.493260
  blue_gain9_ratio=0.493168

  clear_gain8_ratio=1.0
  red_gain8_ratio=1.0
  green_gain8_ratio=1.0
  blue_gain8_ratio=1.0

  clear_gain7_ratio=2.009510
  red_gain7_ratio=2.011340
  green_gain7_ratio=2.012440
  blue_gain7_ratio=2.012773

  clear_gain6_ratio=4.020600
  red_gain6_ratio=4.028348
  green_gain6_ratio=4.028735
  blue_gain6_ratio=4.029882

  # Histogram Configuration.
  # Flag that controls whether the histogram is enabled.
  histo_enable=1
  # Display coordinates go from top left to bottom right.
  histo_roi_left=420
  histo_roi_top=300
  histo_roi_right=560
  histo_roi_bottom=430
  # Weights applied to the RBG color samples to calculate luma.
  # luma values:
  # luma = W_R * R + W_G * G + WB * B
  # with W_R + W_G + W_B = 1024
  histo_weight_r=428
  histo_weight_g=408
  histo_weight_b=188
  #
  # Leakage calculator configuration. The general format is:
  #   leakage = luma_term(luma, dbv) * dbv_term(dbv)
  # The luma_term maps luma into a value and different equations may be used
  # depending on the current DBV value.
  # Similar, the dbv_term maps DBV into a value and may also use different
  # equations.
  # Each line represents one equation, and is of the format:
  #   start-dbv end-dbv equation-type {coefficients}
  # This means the equation applies to the DBV range [start-dbv .. end-dbv].
  # There are two equation types currently:
  #    0: Polynominal: c0 + c1*L + c2*L^2 + .. + ci*L^i
  #    1: Natural Log: c0 + c1*ln(L + c2)
  histo_luma_eq0=0 2047 0 0 3.9E-3
  histo_dbv_eq0=0 2047 0 9.000003E-1 1.03805E-3

  # The maximum brightness (DBV) value up to which histogram is active.
  # This value should match one of the itime_table_brightness values.
  histo_max_brightness=2047
  # Minimum change needed for a leakage value to be reported, i.e.,
  # min_change = MAX(min_change_value, current_leakage_val * min_change_rate)
  histo_min_change_value=0.01
  histo_min_change_rate=0.01
  # Histogram polling interval in ms.
  histo_polling_interval=50
  # Fallback luma value to use when histogram returns error (e.g., due to DRM).
  histo_fallback_luma=128.0

# TMD3719 proximity sensor.
+/dev/tmd3719/0/prox
  auto_baseline=1
  burst_delay_normal=160
  burst_delay_60hz=160
  burst_delay_90hz=160
  burst_delay_aod=0
  hxtalk=1
  pulse_count=1
  vcsel_ma=10
  pd0_far_threshold=50
  pd0_near_threshold=50
  pd1_far_threshold=40
  pd1_near_threshold=60
  # "Low power" operating parameters.
  pulse_len_us=64
  filter_len=4
  skip_count=0
  pdata0_scale=1.195138
  pdata1_scale=1.204765
  gain0=2
  gain1=4
  # "High power" operating parameters.
  hp_pulse_len_us=128
  hp_filter_len=1
  hp_skip_count=0
  hp_pdata0_scale=1.318246
  hp_pdata1_scale=1.320505
  hp_pdata0_offset=2.245979
  hp_pdata1_offset=7.747921
  hp_gain0=1
  hp_gain1=2
  high_power_mode_only=1

# Display Info
+/dev/display_info/0
  # Maximum panel refresh rate.
  panel_max_rr=90
  # Link to ALS attached to this display.
  attached_alsp=/dev/tmd3719/0

# Camera VSYNC
+/dev/camera_vsync/0 # rear telephoto
  intr_id=56
  intr_trigger_type=2
+/dev/camera_vsync/1 # rear ultra-wide-angle
  intr_id=57
  intr_trigger_type=2
+/dev/camera_vsync/2 # front
  intr_id=58
  intr_trigger_type=2
+/dev/camera_vsync/3 # rear
  intr_id=59
  intr_trigger_type=2

# TOUCH (GT9895)
+/dev/gt9895/0
  bus_name=spi0
  bus_freq_hz=10000000
  spi_mode=0
  spi_word_size=8
  cs_gpio=52
  cs_clock_delay_us=1
  gesture_type=4
  intr_id=17
  intr_type=3
  panel_height_pixel=2400
  panel_height_mm=142
  single_tap_min_x=92
  single_tap_max_x=987
  single_tap_min_y=184
  single_tap_max_y=2215
  single_tap_min_frame_count=3
  single_tap_max_frame_count=31
  single_press_motion_tolerance=255
  single_press_max_touch_size=50
  long_press_min_x=438
  long_press_max_x=642
  long_press_min_y=1615
  long_press_max_y=1819
  long_press_min_frame_count=1
  long_press_max_touch_size=50
  long_press_marginal_min_x=396
  long_press_marginal_max_x=684
  long_press_marginal_min_y=1573
  long_press_marginal_max_y=1861
  long_press_monitor_channel_min_tx=6
  long_press_monitor_channel_max_tx=9
  long_press_monitor_channel_min_rx=22
  long_press_monitor_channel_max_rx=25
  long_press_min_node_count=8
  long_press_motion_tolerance_inner=255
  long_press_motion_tolerance_outer=539

# TBN
+/tbn
  tbn_mode=1
  ap2aoc_intr_id=44
  ap2aoc_intr_type=4
  ap2aoc_gpio_id=gpio87
  aoc2ap_gpio_id=gpio74

# VSC.
+/vsc
  quick_pick_up_enable=1
  single_tap_enable=1
  long_press_enable=1

+/vsc/auto_brightness
  # float[3]={LuxToEnter, LuxToExit, RemappedLux}
  lux_remap=-1.0 -1.0 -1.0
  # float[3]={MinDelta, MaxDelta, LuxRatio}
  lux_debounce_up=1 5000 0.15
  lux_debounce_down=0.1 5000 0.1
  # ALS[2], RLS[2], Fusion[2], each containing <maxSampleAgeMsec> and <maxNumOfSamples>
  filter_configs=500 60 500 30 500 90